Search Results

Electric and Hybrid vehicles have standards for emitting enough noise to reduce danger and risk to pedestrians when operating at low speeds. Simulation can help to support development and deployment of these systems while avoiding a time-consuming, test-based approach to design these AVAS (Acoustic Vehicle Alerting System) warning systems. Traditionally, deterministic simulation methods such as Finite Element Method (FEM) and Boundary Element Method (BEM) are used at low frequencies and statistical, energy-based methods such as Statistical Energy Analysis (SEA) are used at high frequencies. The deterministic methods are accurate, but computationally inefficient, particularly when the frequency increases. SEA is computationally efficient but does not capture well the physics of exterior acoustic propagation. An alternative method commonly used in room acoustics, based on geometrical or ray acoustics, is “Ray Tracing” and can be used for sound field prediction.

In order to facilitate the modeling of vehicle drivelines in ADAMS, an ADAMS/View driveline tool was developed with the aid of Mechanical Dynamics, Inc (MDI). Known as Visteon Axle & Driveline Simulation-Dynamics (VADSIM-DYNA) this tool is used to supply customers with driveline models for use in their full vehicle modeling as well as for predicting forces in the driveline. Of specific interest is a method for calculating the mesh point of a hypoid gear set using the geometry of the ring and pinion gears, and a custom force statement for calculation of the mesh point reactions at the center of gravity for both the pinion and ring gears. With the introduction of ADAMS/Driveline, The comapny has worked with MDI to implement VADSIM-DYNA into the base product. With the aid of VADSIM-DYNA the ability to provide customers with ADAMS models of driveline components and systems has been greatly enhanced.

Experimental correlation is essential in the development of analytical simulation models. A methodology for correlating an All-Wheel Drive (AWD) minivan, created with ADAMS/Pre is presented in this paper. The paper is developed in three parts. Presented first are detailed component and system level, static and dynamic tests, including tire tests that were performed for inputs to the model. Then, the static correlation of the model, in particular, the front and rear suspension kinematics and compliance correlation are presented. Finally the dynamic correlation of the model, for the constant radius test and the swept steer test, is discussed. The paper concludes with some observations on AWD modeling.

Recent developments in the prediction of the contribution of wind noise to the interior SPL have opened a realm of new possibilities in terms of i) how the convective and acoustic sources terms can be identified, ii) how the interaction between the source terms and the side glass can be described and finally iii) how the transfer path from the sources to the interior of the vehicle can be modelled. This paper discusses in detail these three aspects of wind noise simulation and recommends appropriate methods to deliver required results at the right time based on i) simulation and experimental data availability, ii) design stage and iii) time available to deliver these results. Several simulation methods are used to represent the physical phenomena involved such as CFD, FEM, BEM, FE/SEA Coupled and SEA.

Electric vehicle makers have largely relied on aluminum to make their cars lighter in hopes of offsetting the weight of the battery pack and reducing overall weight. Distortion of Aluminum welding is a big issue due to Aluminum’s high coefficient of expansion ratios. This paper presents an effective numerical approach to minimize weld-induced distortion in Electrical Vehicle Aluminum assembly structures using welding sequence optimization. A numerical optimization framework based on genetic algorithms and Finite Element Analysis (FEA) is developed and implemented. The shrinkage method calibrated using transient approach, is used for the weld sequence optimization to reduce the computation time. The optimization results show that the proposed calibration approach can contribute substantially to reduce distortion by optimizing weld sequences. It enhances final aluminum assembly quality while facilitating and accelerating design and development.

Recent developments in the prediction of the contribution of wind noise to the interior SPL have opened a realm of new possibilities. The main physical mechanisms related to noise generation within a turbulent flow and the vibro-acoustic transmission through the vehicle greenhouse is nowadays better understood. Several simulation methods such as CFD, FEM, BEM, FE/SEA Coupled and SEA can be coupled together to represent the physical phenomena involved. The main objective being to properly represent the convective and acoustic component within the turbulent flow to ensure proper computation of the wind noise contribution to the interior SPL of a vehicle.

To obtain the maximum output power and fuel economy from an internal combustion engine, it is often necessary to detect engine knock and operate the engine at its knock limit. This paper presents the ability to detect knock using in-cylinder ionization signals on a large displacement, air-cooled, “V” twin motorcycle engine over the engine operational map. The knock detection ability of three different sensors is compared: production knock (accelerometer) sensor, in-cylinder pressure sensor, and ionization sensor. The test data shows that the ionization sensor is able to detect knock better than the production knock sensor when there is high mechanical noise present in the engine.

Electric vehicles are becoming a rapid growing part of the automotive scene. Batteries are considered as one of the most important and challenging components in the development of electric vehicles. The mechanical performance of the battery module is of great interest and the crashworthiness analysis of the battery module is always a critical design aspect. In crash and other severe events, the battery module is subject to impact loads from different directions. The module is designed with a capability to be deformed and collapsed in a controlled manner to mitigate safety critical damage to battery cells inside the module. In the design process, it is necessary to consider the distribution of the impact loads during the crash to minimize the local damage. In this paper, a finite element model is developed and used as an efficient simulation tool to analyze the dynamic behavior of a generic battery module upon crushing and shocking.

This paper describes the applicability of optical imaging techniques to the analysis of the scratch resistance of automotive interior plastic materials. The evaluation of so-called “finger testing” has traditionally relied upon human vision for detection of the initial scratch position. Commonly performed under uniform and defined illumination conditions, the relative contrast difference signified by whitening on a surface as determined by unaided human vision is a highly variable subjective perception; thus individual inspectors may determine the “whitening” point differently. This paper compares test data obtained from both visual and instrumental evaluation methods and discusses the advantages of optical imaging techniques for surface defect analysis.

Designing an effective AVAS system, not only to meet safety regulations, but also to create the expected perception for the vulnerable road user, relies on knowledge of the acoustic transfer function between the sound actuator and the receiver. It is preferable that the acoustic transfer function be as constant as possible to allow transferring the sound designed by the car OEM to ensure the safety of vulnerable road users while conveying the proper brand image. In this paper three different methodologies for the acoustic transfer function calculations are presented and compared in terms of accuracy and calculation time: classic Boundary Element method, H-Matrix BEM accelerated method and Ray tracing method. An example of binaural listening experience at different certification positions in the modeled simulated space is also presented.